Messages

441

General Mach Discussion / Re: creating a second MACH3 profile?

« on: March 29, 2017, 11:48:15 AM »

Start Mach3 loader, choose create profile.  Highlight your existing profile, enter a new name for the duplicate profile eg. AccellMill.

You can then change the motor tuning to whatever you want.  All the other settings, ports, pins, etc. are copied.

442

Mach4 General Discussion / Re: Mach4 logging facility

« on: March 28, 2017, 11:50:48 AM »

Modifying the machine.ini file for the [Log Window] entry to a screen position like 5,5 brings the window into view.  Anyone with less than 1725 pixels in width will not be able to get to the window unless they modify the ini.

Thanks Brett

443

Mach4 General Discussion / Re: Mach4 logging facility

« on: March 26, 2017, 01:14:00 PM »

Don't know if this will work

https://www.dropbox.com/s/0i2jb391x88puox/logging1.avi?dl=0

444

Mach4 General Discussion / Re: Mach4 logging facility

« on: March 25, 2017, 03:35:24 PM »

Thanks Craig,

I was supposed to send a log file demonstrating lathe's miss handling of G31 calls but can't send a log file that doesn't exist.  Seems like mach4 lathe is once again the red headed step sister like mach3 turn.  I guess I have to open another support ticket. 

RT

445

Mach4 General Discussion / Mach4 logging facility

« on: March 25, 2017, 02:02:53 PM »

Can anyone tell me whether they can replicate this problem.  Just load mach4lathe profile and then go to 'Diagnostics->Logging...' and see if you get the standard logging window or a window that has nothing yet has a taskbar presence.  I have it on two machines and get the same invisible window.  If I load Mach4mill I get the standard logging window.

I have re-installed on one of those machines both using ver 3233.

TIA

RT

446

General Mach Discussion / Re: pocketing issues

« on: March 19, 2017, 01:18:18 PM »

All of the above is valuable. If your Z axis is slightly non perpendicular to either the X or Y axis ( not trammed to the bed)you will see exactly what you are referring to, small step like  line on one side of the pocket.

A poor man's way to check is to take a coat hanger, cut it and bend it so that one end can fit in the collett, extend it several inches laterally and then have the other end point to the bed. Lower the Z so that it just touches the bed and then spin it slowly by hand. 180 degrees. If it is not trammed  it will lift or dig in on direction.

447

General Mach Discussion / Re: Double cuts

« on: March 18, 2017, 11:28:42 AM »

post your gcode and micrometer your bit

448

General Mach Discussion / Re: Problems with cutting depth getting shallower

« on: March 18, 2017, 11:25:10 AM »

There is no way for us to tell you what is your problem.  Each machine, even of the same model, may have different characteristics due to shipping, assembly or usage. 

Most likely reasons are binding on axis, tool not being held tightly (debris in collet prevents full closure), motors too small for load, loose coupling on screw.  Then you get to too much acceleration or too fast for the stepper to handle it.  No magic formulas here, sorry.

Search for motor tuning acceleration or missing steps and you will get a plethora of possibilities.

HTH

RT

449

General Mach Discussion / Re: Access to maintenance parameter values

« on: March 17, 2017, 10:48:35 AM »

start a support ticket and see what happens, worth a try.

450

General Mach Discussion / Re: Access to maintenance parameter values

« on: March 16, 2017, 02:53:54 PM »

AFIK all work on M3 has stopped.  I would bet there is a list somewhere at NewFangled that includes all GetParam strings.  You might try posting a PM to Art Fennerty.  http://www.machsupport.com/forum/index.php/topic,27194.0.html

RT