Messages

1231

General Mach Discussion / Re: Motors stalling /growling

« on: June 08, 2019, 03:23:49 AM »

hi,
one idea is left. can you pls do a

G1 X0.1968 F1

in MDI, and confirm that the Motor does exactly one Revolution?

1232

General Mach Discussion / Re: Motors stalling /growling

« on: June 05, 2019, 01:22:07 AM »

can you post a Video with Sound?

1233

General Mach Discussion / Re: Motors stalling /growling

« on: June 04, 2019, 02:25:07 PM »

ok lets start again, i only want to double check everything.

Motor 34HS5435C-37B2:

red    -> DM860A   A
green  -> DM860A   A-
yellow -> DM860A   B
blue   -> DM860A   B-




DM860A:

dip switches current
SW1 -> OFF
SW2 -> OFF
SW3 -> ON

dip switches micro stepping
SW5 -> ON
SW6 -> OFF
SW7 -> ON
SW8 -> ON

wiring signals
PLS+ -> DB25-1205 pin 2
DIR+ -> DB25-1205 pin 3
PLS- -> DB25-1205 pin GND
DIR- -> DB25-1205 pin GND
(only for the x-axis)

V+  -> Power Supply +
GND -> Power Supply GND



BOB DB25-1205 minimal wiring for x-axis

pin 2 -> DM860A PLS+
pin 3 -> DM860A DIR+ 
pin GND -> DM860A PLS-
pin GND -> DM860A DIR-

pin VDD -> external power supply 5V
pin GND -> external power supply GND

JN1 connected
JN2 connected

JN4 here i am not realy sure what the manual is trying to tell me



ethernet smoothstepper minimal wiring

25pole ribbon cable to db25 connector for BOB
ethernet cable to pc
external power supply for 5V connected


motor tuning settings (we discused a lot)
steps/per 8128
vel 60
acc 12






hope i got the mayor things, pls take the the time to go through this list step by step and doublecheck,
i have taken the time to create it.

1234

General Mach Discussion / Re: Motors stalling /growling

« on: June 04, 2019, 01:17:05 PM »

I an using nema 34

ok i was asking for a exact Motor Label/number, because nema 34 is like you say "i drive a green BMW",
there are hundreds of nema 34 brands, and i wanted to doublecheck the Motor wiring.-> waiting  for reply

and the breakout board db25-1205.

here i found a manual

Ok ill set that back to 8128

just to clarify this will not solve the Problem, but the 8128 steps/per is a given value based on your Setup and Needs not
to be modyfied.

1235

General Mach Discussion / Re: Motors stalling /growling

« on: June 04, 2019, 08:03:34 AM »

the 8128 steps/per is a value witch is given trough your microstepping and Resolution of your ballscrew.
in other word's it is fix and no parameter to Play with.

what exact motortype are you using?
what bob are you using?

1236

General Mach Discussion / Re: Motors stalling /growling

« on: June 04, 2019, 05:12:48 AM »

Here is the final settings:                X settings
Y & A axis settings:                         steps 7100
steps: 6940                                    velocity 60
velocity: 59                                     accel    8
accel: 8                                          step pulse 5
step pulse: 5                                   dir pulse  5
dir pulse: 5

why did you not use the recommended 8128 steps/per ?

1237

Works in progress / Re: Well i finally uploaded my 6 axis screen, was 5 axis.......

« on: June 04, 2019, 03:18:46 AM »

i Need your Bitmaps as well

1238

Works in progress / Re: Well i finally uploaded my 6 axis screen, was 5 axis.......

« on: June 04, 2019, 02:18:53 AM »

tested here (in 1024 Standard srceen set) OEMButton255 OEMLED91 worked.
i have used machscreen.

1239

Works in progress / Re: Well i finally uploaded my 6 axis screen, was 5 axis.......

« on: June 03, 2019, 12:47:02 PM »

Axis inhibited C LED is 91 in my list? not 90

1240

VB and the development of wizards / Re: off the shelf auto zero script issue

« on: June 03, 2019, 12:37:41 PM »

so i assume in Config -> General Config -> General Configuration -> G04 Dwel in MS is enabled?
Keep it like it is, but the original macro code used G04 for wait step's based on seconds.
i replaced them to sleep's witch are not based on any Setting.