Messages

1

General Mach Discussion / Re: What's The latest version of mach 3 that is proven reliable

« on: April 27, 2024, 12:34:45 AM »

Ok, I may do that. This version works great, except that I have to add M04 at the bottom of the tap cycle.
Is there a way to go into the tap wizard and change that?

2

General Mach Discussion / What's The latest version of mach 3 that is proven reliable

« on: April 26, 2024, 12:34:15 AM »

I'm still using a version of mach 3 that came out in 2012.
Last week I tried to do some power tapping, and it wouldn't reverse the spindle.
A buddy of mine said that I needed to upgrade to the latest version
What is needed for this?
Do I need to backup my settings?
Thanks in advance

Jackal

3

General Mach Discussion / Re: Does my cable from pendant to control need to be shielded wire?

« on: August 19, 2023, 12:02:57 AM »

Got it fixed

4

General Mach Discussion / Does my cable from pendant to control need to be shielded wire?

« on: August 17, 2023, 10:43:10 AM »

I'm replacing the cable from my pendant.
It has a MPG and a E stop on it.
The old cable is breaking down and insulation is crumbling.
Also, a straight cable would be easier to use instead of the coiled.
Does the new cable new to be shielded?
Thanks,
Jack

5

General Mach Discussion / Re: E stop won't reset on mach3

« on: July 17, 2022, 09:06:53 PM »

Any ideas where to start?
I'm  going to reroute new wire to the Estop switches.
Bypass all the old wires.
Then, check settings on the pins page.

6

General Mach Discussion / E stop won't reset on mach3

« on: July 16, 2022, 01:43:12 PM »

Hello,
I have a Hurco mill that was retrofitted in 2011.
It has ran great over the years.
After sitting idle (no power) for about 5 months,when I power it on the Estop won't  reset.
Both Estop buttons and wiring check ok.
The Estop light on my control panel stays lit up, and the main screen 'reset flashes'.
It has been so long since  I've  messed with the pins and settings in mach.
Can someone tell me which pins in the settings I can check/reset/ toggle?

Thanks  so much.

7

General Mach Discussion / When doing an emergency backup of mach what should be saved?

« on: November 07, 2021, 10:06:55 AM »

I recently had a scare where my computer that ran mach3 on my mill was acting up.
There is a copy of my .xml file on a jump drive, but since the build was so long ago, what screen pics. would be helpful?
My thoughts were to take a pic of each screen  with the current settings,too.
Any other advice or shortcuts  to help with this procedure.

Thanks,
Jack

8

General Mach Discussion / Re: Wanting to upgrade mach 3 to a newer version

« on: October 16, 2021, 11:23:01 AM »

I think you will find that Version R3.043.062 is the best one to use.

Tweakie.

Thanks for that info. Much appreciated.👍👍👏👏💯

9

General Mach Discussion / Re: Wanting to upgrade mach 3 to a newer version

« on: October 16, 2021, 02:43:57 AM »

Tweakie,
Thanks  for that  info.
When I searched Google,  it just showed the latest version on several host sites.
Will let y'all  know how update goes.

10

General Mach Discussion / Re: Wanting to upgrade mach 3 to a newer version

« on: October 16, 2021, 01:16:33 AM »

Any ideas where I can download a  newer version? Not necessarily  the newest, maybe something around 2013???