Messages

1061

General Mach Discussion / Re: Z moves down after Ref All home and hits base

« on: January 21, 2020, 02:14:54 AM »

if it is an optical sensor, i think there should be an external power supply (5V) somewhere.
is there no Manual of the Controller box?

1062

General Mach Discussion / Re: Z moves down after Ref All home and hits base

« on: January 20, 2020, 12:00:51 PM »

normaly first Thing is to figure out how they are wired to your Controller/ parallel port.
on the Picture you posted i can't se any wiring at all??!

and after the wiring is clear in Config -> Ports&Pins -> Inputs

1063

Mach SDK plugin questions and answers. / Re: Plugin that works for Chinese mpg pendant

« on: January 20, 2020, 11:43:58 AM »

small question, witch light Change on diagnostic Screen?

you are using ZASto's Brains now, all Trigger' oemcodes set to -1 in Config System hotkeys?

all plugin's  related to any mpg deleted from plugin Folder?

pls post your Profile XML.

1064

General Mach Discussion / Re: lost steps/ motor stall with tripple beast

« on: January 20, 2020, 02:11:30 AM »

hello, i think your Problem is the power supply, just deconnect your 4th axis (Motor) and try again.

Hallo, ich denke das Problem liegt an dem Netzteil, einfach mal die 4te Achse abklemmen (Motor) und dann noch mal probieren.

1065

General Mach Discussion / Re: Z moves down after Ref All home and hits base

« on: January 20, 2020, 02:04:24 AM »

Ok, so if I move my Z all the way up, there is no change in the diagnostic screen

so check your Limit Switch für z-axis

Yes, as the Z moves up, the numbers increase positive

thant is ok

In diagnostic screen, if I press z (picture yellow circle) it moves down

then Change Config -> Homing/Limits -> z-axis -> Home Neg.

1066

Mach SDK plugin questions and answers. / Re: Plugin that works for Chinese mpg pendant

« on: January 19, 2020, 11:26:05 AM »

orange/black is the com of all Switches, and for switching Inputs at a parallel port they Need to be taken to gnd.

1067

Mach SDK plugin questions and answers. / Re: Plugin that works for Chinese mpg pendant

« on: January 19, 2020, 07:50:05 AM »

ok corrected Version

Green- 2 pin ( mpg A+)
White- 3 pin ( mpg B+ )
Config -> Ports&Pins -> Encoder/MPS -> MPG1 Enabled | A-Port = 2 | A-Pin = 2 | B-Port = 2 | B-Pin = 3

Green&black- 1 pin ( jog on led +5v )
White&black- gnd ( jog on led gnd)

 this is only the led, we will take care later


Yellow- 4 pin ( select x axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 4
System Hotkeys -> Trigger#1 OEM Code = 259

Yellow&black- 5 pin ( select y axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#2 Enabled | Port = 2 | Pin = 5
System Hotkeys -> Trigger#2 OEM Code = 260

Brown- 6 pin ( select z axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#3 Enabled | Port = 2 | Pin = 6
System Hotkeys -> Trigger#3 OEM Code = 261

Brown&black- 7pin ( select a axis )
 Config -> Ports&Pins -> Input Signal -> OEMTrigger#4 Enabled | Port = 2 | Pin = 7
System Hotkeys -> Trigger#4 OEM Code = 262


Gray- 8pin ( x1 )
 Config -> Ports&Pins -> Input Signal -> OEMTrigger#5 Enabled | Port = 2 | Pin = 8
System Hotkeys -> Trigger#5 OEM Code = 265

Gray&black- 9pin ( x10 )
 Config -> Ports&Pins -> Input Signal -> OEMTrigger#6 Enabled | Port = 2 | Pin = 9
System Hotkeys -> Trigger#6 OEM Code = 266

Orange- 10pin ( x100 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#7 Enabled | Port = 2 | Pin = 10
System Hotkeys -> Trigger#7 OEM Code = 267

Orange&black- +5v ( com for selector )
this is wrong, Needs to be connected to GND

1068

Mach SDK plugin questions and answers. / Re: Plugin that works for Chinese mpg pendant

« on: January 19, 2020, 04:19:32 AM »

and as ZASTo sayed

GND from outside source and GND of your Parallel port should be connected pin 18-25

1069

General Mach Discussion / Re: Program pause command?

« on: January 19, 2020, 04:02:16 AM »

why are you not using M6T?? and set toolchange to "Stop spindle wait for Cycle Start" ?

1070

Mach SDK plugin questions and answers. / Re: Plugin that works for Chinese mpg pendant

« on: January 19, 2020, 03:57:31 AM »

Green- 2 pin ( mpg A+)
White- 3 pin ( mpg B+ )
Config -> Ports&Pins -> Encoder/MPS -> MPG1 Enabled | A-Port = 2 | A-Pin = 2 | B-Port = 2 | B-Pin = 3

Green&black- 1 pin ( jog on led +5v )
White&black- gnd ( jog on led gnd)

this is only the led, we will take care later


Yellow- 4 pin ( select x axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 4
System Hotkeys -> Trigger#1 OEM Code = 259

Yellow&black- 5 pin ( select y axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#2 Enabled | Port = 2 | Pin = 5
System Hotkeys -> Trigger#1 OEM Code = 260

Brown- 6 pin ( select z axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 6
System Hotkeys -> Trigger#1 OEM Code = 261

Brown&black- 7pin ( select a axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 7
System Hotkeys -> Trigger#1 OEM Code = 262


Gray- 8pin ( x1 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 8
System Hotkeys -> Trigger#1 OEM Code = 265

Gray&black- 9pin ( x10 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 9
System Hotkeys -> Trigger#1 OEM Code = 266

Orange- 10pin ( x100 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 10
System Hotkeys -> Trigger#1 OEM Code = 267

Orange&black- +5v ( com for selector )
this is wrong, Needs to be connected to GND