Messages

1951

VB and the development of wizards / Re: center axis rotating axis

« on: March 12, 2018, 06:17:06 AM »

try this.
please test carefully, not tested.

y-axis must be in front of (-) part in a-axis, z-axis in height to probe.

Code: [Select]


Sub Main()

'get Diameter from user
Begin Dialog TextBoxSample 16,30,180,96,"enter digfilename"
OKButton 132,20,40,14
Text 8,8,132,8,"Diameter of part:"
TextBox 8,20,100,12,.TextBox1
End Dialog
Dim Dlg1 As TextBoxSample

Dialog Dlg1
diameter = CDbl(Dlg1.TextBox1)

If diameter <=1 Then
MsgBox "Diameter wrong !"
Exit Sub
End If
  
Call SetDRO(0,0)
Call SetDRO(1,0)
Call SetDRO(2,0)

Xpos = GetParam("XDRO")
Ypos = GetParam("YDRO")
Zpos = GetParam("ZDRO")

Fcurr = GetParam("FeedRate")
SP = 80 ' avanzamento prima palp impostare diametro mm del cerchio da palpare
VSP = "F200" ' velocita avanzamento prima palp
bkSP = 3 ' ritorno dopo palp mm
VbkSP = "F240" ' velocita ritorno
Spp = 5 ' avanzamento seconda palp mm
VSpp = "F40" ' velocita seconda palp


Code "G31 Y" & (GetParam("YDRO")+SP) & (VSP)
While IsMoving()
Wend

Code "G0 Y" & (GetParam("YDRO")-bkSP) & (VbkSP)
While IsMoving()
Wend

Code "G31 Y" & (GetParam("YDRO")+Spp) & VSpp
While IsMoving()
Wend

B=GetParam("YDRO")

Code "G0 Y" & (GetParam("YDRO")-bkSP) & (VbkSP)
While IsMoving()
Wend

'Z up
Code "G0 Z" & Zpos + (2*diameter)
While IsMoving()
Wend

'Y behind part
Code "G0 Y" & Ypos + (2*diameter)
While IsMoving()
Wend

'Z down
Code "G0 Z" & Zpos
While IsMoving()
Wend

Code "G31 Y" & (GetParam("YDRO")-SP) & (VSP)
While IsMoving()
Wend

Code "G0 Y" & (GetParam("YDRO")+bkSP) & (VbkSP)
While IsMoving()
Wend

Code "G31 Y" & (GetParam("YDRO")-Spp) & VSpp
While IsMoving()
Wend

A=GetParam("YDRO")
measuredY = B-A

Code "G0 Y" & (GetParam("YDRO")+bkSP) & (VbkSP)
While IsMoving()
Wend

'Z up
Code "G0 Z" & Zpos + (2*diameter)
While IsMoving()
Wend


Code "G0 Y" & (A+(B-A)/2)
SetParam("FeedRate",Fcurr)

MsgBox ("Measurement Y: " & nFmt(measuredY,3) & " mm")

End Sub






1952

General Mach Discussion / Re: Double touch when using auto zero. Plate grounded error.

« on: March 12, 2018, 02:16:11 AM »

but if you go to diagnostic Screen you can see the digitize LED working,
Off if your probe is free, ON if you touch your probe to te plate ?

1953

General Mach Discussion / Re: Double touch when using auto zero. Plate grounded error.

« on: March 11, 2018, 10:11:05 AM »

copy your code into VB Scripter window.
use the ||> step button and step through the code,
than you will see exactly when the error occurs.

1954

General Mach Discussion / Re: Mach3 Pendant

« on: March 11, 2018, 06:23:44 AM »

ok there is not much what can go wrong in this brain.

i have no idea why this is Happening.

i would in a first step add a and to eatch rung

oemtrigger1 AND LED15(step mode) AND LED83 (Jog on) = MPG1 JogX

Thomas

1955

VB and the development of wizards / Re: laser / web centering

« on: March 10, 2018, 08:09:25 AM »

this should do what you want

Code: [Select]


Sub Main
  Begin Dialog SelectCentering 31,32,125,96,"Select Centering"
OKButton 20,68,40,14
CancelButton 70,68,40,14
GroupBox 20,8,72,52,"centering",.GroupBox1
OptionGroup .OptionGroup1
OptionButton 26,24,54,8,"laser",.OptionButton1
OptionButton 26,40,54,8,"web"  ,.OptionButton2
  End Dialog

  Dim Dlg1 As SelectCentering
  Button = Dialog (Dlg1)
 
  If Button = 0 Then Exit Sub
  Selected  = Dlg1.OptionGroup1

  'laser is selected
  If Selected = 0 Then
Speak ("confermare ZERO PEZZO WEB") 'Avviso Vocale
Message "************  INIZIO ZERO PEZZO WEB ************"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE ZERO PEZZO WEB")
SetUserLED(1103,1) 'close Klause's video window
Call SetOemDRO(3,80) 'reset jog rate to 80%
Xs=GetOemDRO(59) 'read Xscale DRO
Ys=GetOemDRO(60) 'read Yscale DRO
Xmove = -140.000 'enter your camera offset here
Ymove = -32.700 'enter your camera offset here
Code "G91 f500 X" &Xmove & "Y" &Ymove 'make incremental move
While IsMoving () 'wait while that happens
Wend
Code "G90" 'go back to absolute moves
DoOEMButton (1008) 'zero X axis DRO
DoOEMButton (1009) 'zero Y axis DRO
Code " (   HOMING CENTRO COMPLETATO)" 'message for status bar     
Speak ("homing centro completato") 'Avviso Vocale   
  End If
 
  'web is selected
  If Selected = 1 Then
Speak ("confermare ZERO PEZZO WEB") 'Avviso Vocale
Message "************  INIZIO ZERO PEZZO WEB ************"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE ZERO PEZZO WEB")
SetUserLED(1103,1) 'close Klause's video window
Call SetOemDRO(3,80) 'reset jog rate to 80%
Xs=GetOemDRO(59) 'read Xscale DRO
Ys=GetOemDRO(60) 'read Yscale DRO
Xmove = -130.000 'enter your camera offset here
Ymove = -25.700 'enter your camera offset here
Code "G91 f500 X" &Xmove & "Y" &Ymove 'make incremental move
While IsMoving () 'wait while that happens
Wend
Code "G90" 'go back to absolute moves
DoOEMButton (1008) 'zero X axis DRO
DoOEMButton (1009) 'zero Y axis DRO
Code " (   HOMING CENTRO COMPLETATO)" 'message for status bar     
Speak ("homing centro completato") 'Avviso Vocale     
  End If
   
End Sub







1956

VB and the development of wizards / Re: center hole script

« on: March 09, 2018, 11:50:01 AM »

have a try this does what you want.

Code: [Select]

Speak ("ricerca centro pezzointerno") 'Avviso Vocale
Message "RICERCA CENTRO PEZZO INTERNO"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE RICERCA CENTRO PEZZO INTERNO")

Sleep (1000) ' pausa di 1 secondi
Speak (" CONFERMARE centro pezzo interno") 'Avviso Vocale
Message "INIZIO CENTRO PEZZO INTERNO"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE CENTRO PEZZO INTERNO")


  
Call SetDRO(0,0)
Call SetDRO(1,0)
Xpos = GetParam("XDRO")
Ypos = GetParam("YDRO")
Fcurr = GetParam("FeedRate")
SP = 80 ' avanzamento prima palp impostare diametro mm del cerchio da palpare
VSP = "F200" ' velocita avanzamento prima palp
bkSP = 3 ' ritorno dopo palp mm
VbkSP = "F240" ' velocita ritorno
Spp = 5 ' avanzamento seconda palp mm
VSpp = "F40" ' velocita seconda palp

Code "G31 X" & (GetParam("XDRO")+SP) & (VSP)
While IsMoving()
Wend

Code "G0 X" & (GetParam("XDRO")-bkSP) & (VbkSP)
While IsMoving()
Wend

Code "G31 X" & (GetParam("XDRO")+Spp) & VSpp
While IsMoving()
Wend

B=GetParam("XDRO")

Code "G0 X" & Xpos

Code "G31 X" & (GetParam("XDRO")-SP) & (VSP)
While IsMoving()
Wend

Code "G0 X" & (GetParam("XDRO")+bkSP) & (VbkSP)
While IsMoving()
Wend

Code "G31 X" & (GetParam("XDRO")-Spp) & VSpp
While IsMoving()
Wend

A=GetParam("XDRO")

measuredX = B-A

Code "G0 X" & (A+(B-A)/2)
While IsMoving()
Wend

Code "G31 Y" & (GetParam("YDRO")+SP) & (VSP)
While IsMoving()
Wend

Code "G0 Y" & (GetParam("YDRO")-bkSP) & (VbkSP)
While IsMoving()
Wend

Code "G31 Y" & (GetParam("YDRO")+Spp) & VSpp
While IsMoving()
Wend

B=GetParam("YDRO")

Code "G0 Y" & Ypos

Code "G31 Y" & (GetParam("YDRO")-SP) & (VSP)
While IsMoving()
Wend

Code "G0 Y" & (GetParam("YDRO")+bkSP) & (VbkSP)
While IsMoving()
Wend

Code "G31 Y" & (GetParam("YDRO")-Spp) & VSpp
While IsMoving()
Wend

A=GetParam("YDRO")

measuredY = B-A

Code "G0 Y" & (A+(B-A)/2)
SetParam("FeedRate",Fcurr)

MsgBox (" Measurement X: " & nFmt(measuredX,3) & " mm  Measurement Y: " & nFmt(measuredY,3) & " mm")


the Measurement Y sjould be the Diameter of hole - Probediamater

1957

General Mach Discussion / Re: Mach3 Pendant

« on: March 09, 2018, 11:03:11 AM »

would be helpful if you post your brain/script witch controls the axis selction.

1958

VB and the development of wizards / Re: center hole script

« on: March 09, 2018, 09:41:15 AM »

do you mean you want a messeage box witch Shows the measured X and Y Diameter ?

1959

General Mach Discussion / Re: Limit switch set up on Mach3 with the Gecko g540

« on: March 09, 2018, 09:39:58 AM »

Hello Tony,

glad to hear that everthing is ok now.
i am happy that i was able to set a few Triggers for the drirection to go.

Thomas

1960

General Mach Discussion / Re: Limit switch set up on Mach3 with the Gecko g540

« on: March 08, 2018, 03:39:47 PM »

i would use "ENABLE 1"  instead of "CHARGE PUMP".

i never understood "CHARGE PUMP", maybe depending of my bad english.

sorry i will finish for today, allready late here in Bavaria.

but i think we are very Close.