Messages

121

Mach4 General Discussion / Re: Upgraded to build 4534 and single block does not work

« on: January 07, 2021, 11:28:43 AM »

As long as they're fixing screens how about having them add the 'Machine diagnostics' tab to the lathe set and fix the X axis DRO in the lathe set so that it is not read only and the 'help docs?' button always enabled.

RT

122

Mach4 General Discussion / Re: How to display C axis in Lathe graphics?

« on: January 01, 2021, 11:15:38 AM »

I use the C axis for a few things, it would be nice to have but I can live without it.

123

Mach4 General Discussion / Re: X Box here we come!

« on: December 24, 2020, 07:21:06 PM »

Brian,  Please check the latest release.  The joy sticks map both left and right the same as well as the JS up and down.  At least for me.  Also the descriptor strings for half of the choices are revered instead of reversed.
Oh, BTW, Merry Christmas!

RT

124

Mach4 General Discussion / Re: X Box here we come!

« on: December 23, 2020, 01:56:31 PM »

One more item to consider.  If any of the controls are pressed when in the locked mode activate the rumble.

125

Mach4 General Discussion / Re: X Box here we come!

« on: December 23, 2020, 10:41:35 AM »

I have used the left joy for x and y and right for z on my  mill.  I question whether holding down the right JS and moving it would jump back to continuous as you released it.  Would have to try and see how that worked. I would rather be in constant mode unless I held one of the triggers for continuous.  Just me.

RT

126

Mach4 General Discussion / Re: X Box here we come!

« on: December 23, 2020, 10:07:15 AM »

I guess it would be useful to have others weigh in.  In Lee's old Mach3 plugin it was always an issue whether you were in continuous or incremental mode if you used the same buttons/joystick.  The incremental is the most useful for me.  I will use it as is, nice piece of work.

RT

127

Mach4 General Discussion / Re: X Box here we come!

« on: December 23, 2020, 09:14:43 AM »

Easy and not complex....hmm.  Oh, that's easy (easy for me to say )

I would envision adding 3 mode radio buttons to you key selection dialog, Continuous Jog, incremental Jog and Mouse Mode.
now each key has a table of 3 actions that can be stored depending on which radio button is active.  In your code when a key is active you check to see if mouse mode is active else if incremental else continuous. 

With regards to incremental jog, when a jog key is pressed a state is set and action taken until that key value goes back to 0 when the state is reset while set the action is not repeated.

Just a suggestion,

RT

128

Mach4 General Discussion / Re: X Box here we come!

« on: December 22, 2020, 03:36:08 PM »

Had a few minutes to play around with this on my mill.  Super useful! Thank you!

ok, you asked.... and we will respond 

Is there a way to toggle between step and continuous jogging with the joysticks?
Can you cycle through the jog increments?

What do the jog/MPG# and MPG# do?
The mouse control is cool but can you set it up so that if mouse is enabled the joysticks move the mouse and when not they have other function?

RT

129

Mach4 General Discussion / Re: X Box here we come!

« on: December 22, 2020, 12:16:52 PM »

Brian,  I thought you were onto the problem with removing Daz's plugin.  Deleted those files as well as pokeys and pmdx.  No luck.  Rebooted and fired up M4.  Same result

Thanks for trying

RT

130

Mach4 General Discussion / Re: X Box here we come!

« on: December 22, 2020, 11:45:04 AM »

Still can't figure out why it doesn't show in the Config->Plugins
Latest Dev release and latest mcXbox download.  Would really appreciate any help.

TIA

RT